Heating and cooking stove Inzhkomtsentr VVD Firebird

is one of the leaders among Russian manufacturers of bath equipment. The stoves of this manufacturer can be used both in bathhouses for several people, and in large steam rooms intended for a large number of visitors. Depending on the fuel used, bath equipment from this manufacturer is divided into wood-burning (for all types of solid fuel), combined (for wood and gas) and electric. Ermak sauna stoves are designed to heat water, produce steam and heat adjacent rooms. This manufacturer produces two types of equipment: regular and elite . Conventional stoves are made of high-strength steel with a thickness of 3-4 mm and cast iron grates. Elite models are made of 3 mm thick stainless steel, cast iron grates and a door with high temperature resistant glass.

Valery

I decided to write a review about the Hephaestus PB 03M stove and the facing made of soapstone. The bathhouse was built, the most difficult stage was choosing a cast iron stove. I came across this store, I was pleased with the selection, and the prices were not too high. Well done guys, they selected everything according to our wishes, an engineer came, took measurements and sent the specifications. We paid. Then the team arrived and installed the stove and cladding. The steam is very good! Thank you for your efficiency and responsiveness, it is a pleasure to cooperate with you.

Product Features

Classic devices are made of thick steel sheet, so they weigh more than “elite” ones. The use of stainless steel in production does not reduce strength and quality . The classic series differs:

• non-deforming firebox;
• door with cooled handle;
• remote pre-furnace tunnel;
• heating the heater from 4 sides;
• a system that evenly distributes heat;
• protection from infrared rays;
• functionality and ease of installation.

Elite series, in addition to the qualities listed above, are distinguished by:

• heat-resistant glass in the door;
• firebox made of stainless heat-resistant steel;
• enlarged stainless steel heater.

Both classic and luxury appliances are available with different capacities, which allows you to choose a stove for any area. The cost of basic models is approximately 10 thousand rubles, which allows them to be used in a summer cottage.
Elite products are more expensive - 15-30 thousand rubles and are suitable for a bathhouse in a country house. install stoves from Ermak , but keep in mind that a foundation is required (the weight of the stove, stones and water tank can reach 300 kg). To connect an electrically heated model, you definitely need a specialist.

Nikolay Sergeevich

When choosing a stove for the bathhouse, I was guided by reliability and economic indicators; Master Sauna consultants helped me choose a stove for the Hephaestus PB-03ms bathhouse. I choose my things quite carefully because... I am a former design engineer myself. What caught your attention? The design of the combustion system, equipped with the function of post-burning gases with a flame extinguisher and turbulent fins, allows you to heat the stove up to 750 degrees, while the temperature in the chimney is only 300 degrees. Of course, it is difficult to check these indicators, but the bathhouse warms up very quickly and the stone heats up evenly. I liked that the cast iron stove is 60 mm thick and keeps heat for a long time. I am completely satisfied with my choice, the oven is simply wonderful, many thanks to the company’s employees.

Types of Ermak wood-burning sauna stoves

All types of Ermak 16 and Ermak 20 stoves have a remote firebox, so they can be heated from another room. 17% chromium is added to the steel of Elite models.
This equipment can be used not only in a Russian bath, but also in a sauna. The Elite 20 PS model is distinguished by the presence of fireproof glass in the door, which creates the effect of a fireplace. The latest models of the manufacturer: Ermak 30 and Ermak 50 stoves. They are more voluminous and heavier . Ermak 30 can heat a steam room with a volume of up to 35 m3. This stove requires a chimney with a diameter of 130 mm. The heater can be open (to produce wet steam) and closed (to produce dry steam). For an open heater you need 40 kg of stones, for a closed one - 25 kg. The manufacturer recommends installing a water tank with a volume of 55-65 liters. This model can be with a glass door, installation of a heat exchanger is allowed.

Both versions of the Ermak 50 model are designed for steam rooms with a volume of up to 50 m3. They require a chimney with a diameter of 115 mm and 120 kg of stones. This model does not have a heat exchanger. The manufacturer recommends installing a tank with a volume of 55-65 liters. The presence of panoramic glass creates the effect of a fireplace.

Karina

We purchased the Hephaestus PB-04 stove in the spring for our new bathhouse. Since our bathhouse is not very large, the Hephaestus PB-04 mesh stove was ideal for us according to its characteristics. We liked this stove because of its modern design, neat dimensions and, of course, the material, since cast iron is an ideal material for such products. And after the first fire, we were convinced that we had not made a mistake in our choice. To our great joy, the stove turned out to be very economical, it required very little wood to heat up, our bathhouse immediately heated up, and what is good news is that in the morning it was very warm in the bathhouse, thanks to such a wonderful stove.

Combined and electric ovens

In addition to wood-burning stoves, it also produces equipment that can be heated with both wood and gas - a gas burner is installed on a wood-burning stove . These models can be used in both a Russian bath and a sauna. Such equipment can warm up several rooms: a steam room, a locker room, a shower room, prepare steam and heat water.

The most popular are Uralochka 20 T with a power of 19 kW (for a room with a volume of up to 20 m3) and Uralochka 20N with a power of 12 kW (for a room with a volume of up to 12 m3). The firebox is made of stainless steel 3 mm thick, the stove is equipped with SABK-T automation, a temperature sensor, a pressure regulator and a stepped chimney. Automation maintains a uniform temperature in the room and turns off the equipment when the gas supply stops , the air overheats or the draft decreases.

The ash pan and main burner are ignited manually. Additionally, you need to purchase a water tank with a capacity of 50 liters. The main advantages of gas-fired equipment:

• modern are used in production ;
• compact size and attractive design;
• the equipment is environmentally friendly, safe and fire resistant ,
• high maintainability ;
• long service life.

Electric stoves from Ermak are most often purchased for saunas . They are easy to install and do not require special care. Electric models are environmentally friendly (no fumes are released).
A wide range of models allows you to choose equipment for almost any area. Electric sauna stoves are made of stainless steel, so they last a long time. The main body is coated with mirror steel to enhance convection and improve appearance. These models are popular not only in Russia - they are also readily purchased abroad.

Reviews of Ermak products

Ermak stoves with a heat exchanger and water tank, as well as other models, have reviews from real customers, which you can read below:

1. We already have experience using this unit. When the firebox door is open, the structure heats up within a few hours. The tank of our Ermak stove is designed for 60 liters. water, and the basket holds 60 kilograms of stone. Installed on a pre-prepared floor surface made of two layers of bricks. So far there are no complaints;
2. We bought it on the recommendation of a friend, since he has the same fireplace installed in his bathhouse. Initially, the presence of thin steel walls caused concern, but this did not affect the operation of the stove in any way. Among the shortcomings, I will highlight the clearly visible seams, but cleaning the ash pan is quite convenient. On average, it takes about 1-1.5 hours to heat water in a bathhouse. I would also include the presence of a pre-flow tunnel as an advantage;
3. I’ve been using the Ermak 16 model for about a month now. In my opinion, the design is easy to maintain, efficient, and provides quick heating of the bath in 2 hours. The heat exchanger and water tank, depending on your wishes, can be installed on the right or left side. Additional fittings and accessories (basket, tank) can be purchased either together with the heating device or separately. Conclusion: good value for money and high quality;
4. A year ago we purchased the Ermak 24 model. I use various types of wood for the firebox, which is why aspen logs are often needed for ignition. I think that if birch logs were used, the firebox would be no less effective. The combustion chamber is equipped with a door with tempered glass, which has a truly working self-cleaning function;
5. We bought an inexpensive Ermak hearth located in Economy class. For this price category, the quality of the stove is appropriate and I am completely satisfied. I installed a fireplace in the bathhouse at the dacha. It is precisely for such conditions that it is suitable. For large saunas and baths, it is best to dig more expensive Premium class fireplaces from the manufacturer, since they are designed for a large area.

Main components and components of Ermak brand furnaces

The Ermak stove for saunas and baths is shown in the photo in non-working condition

Domestic oven: top view

The stove is intended for installation in a sauna and is equipped with an additional hole for loading stone directly on the body

How to choose a stove for a wood-burning sauna

To correctly evaluate and make a choice, experts recommend proceeding in the following order:

• The first thing you need to pay attention to is the material used for the walls, heaters, and most importantly, the furnace firebox. If the description states special cast iron, then its use is confirmed by references to certificates, GOST standards and the manufacturer of the cast iron sheet. All this can be checked online;
• The second condition is the quality of workmanship. A cast-iron wood-burning stove should not have gaps or loose fits at the joints of the plates, otherwise carbon monoxide may accumulate in the bathhouse or steam room;
• The third parameter is to check the passport for the possibility of operating a cast-iron stove at different power levels, using raw and large wood. In winter, the bathhouse will have to be heated with not the driest logs, and in addition, maximum heat output is needed so that the preparation of the steam room does not take 5-6 hours. In summer, the process is reversed; a cast iron stove must heat effectively even with a small amount of firewood, otherwise the steam room, especially in mini-saunas, can easily overheat.

If all of the above points are met, then pay attention to the layout of the furnace and its thermal power. The required amount of heat for a bath is calculated using a special method and another 15-20% of the reserve is added. Knowing its value, you can compare the required power with that declared in the stove’s passport. At the same time, you can check the heating capacity of a cast-iron wood-burning stove by dividing the volume of the firebox in liters by a factor of 2. You will get the value in kW/h.

Classic version of the heater with a cast iron portal and firebox

Facing function

The main function of the Hephaestus stove lining is to create a real Russian bathhouse microclimate in the steam room. After installing (assembling) the lining around the stove, it becomes possible to regulate the air temperature in the steam room and maintain the required level of humidity for a long time. This stove lining creates a very mild climate in the steam room, stopping hard infrared radiation 100%. The heater of the Hephaestus stove with a deposit, covered with cladding, heats up faster to higher temperatures, producing even higher quality finely dispersed steam. Such steam is an integral part of the Russian bath; it does not burn the skin, unlike large drops of “raw” steam, does not dry out the lungs and allows you to enjoy bath procedures without time limits.

High power furnace models

For steam rooms with an area of ​​10 m2 or more, the capabilities of the 12th and 16th models are clearly not enough, and meanwhile, more and more lovers of strong steam prefer to build baths with large steam rooms.

suggests using its stoves Ermak 20 and Ermak 24, with a power of 20-24 kW, on wood and briquette fuel, and Uralochka 20 on gas. According to the owners' reviews, the Ermak 24 stove is ideal for a country house with an attached bathhouse, while the 20th model is best installed in a separate sauna or steam room.

In both cases, the design of the combustion chamber with a built-in heat exchanger copes well not only with heating the steam room, but also with heating the entire bathhouse, even taking into account the partial selection of hot water by the washing department or summer kitchen.

Soapstone stoves

Cladding with coil or soapstone tiles is considered justified only for stoves made of thin alloy steel with a high chromium content. Even with wood, the firebox becomes white hot and greatly burns the air in the steam room.

Sometimes the manufacturer uses soapstone to protect against thermal shock. It happens that an accidentally overturned ladle of boiling water past the heater onto a hot cast iron body causes cracks or punctures in the cast iron.

In other cases, the use of soapstone is dictated more by design than by technical operating conditions.